XKM/JXT1 系列“T”接端子及电缆“T”接箱

当前位置:

产品中心

XKM/JXT1 系列“T”接端子及电缆“T”接箱

XKM/JXT1 系列“T”接端子及电缆“T”接箱

如果您有任何问题可以联系我们!
联系我们
XKM/JH27-300mm2
订货号(Order No.): 110176
 
一、产品概述 Genera
XKM/JXT1系列"T”接端子及电缆"T”接箱主要适用于建筑、工业电气设备中作主电缆(干线)不能切断时的"T”形分线连接用。以往导线的"T”形连接通常采用剥开主干线绝缘、将分支导线绕接在主干线上、包上绝缘包布的方法。这种接线方法直接的危害是可靠性差、接点电阻大,极易引发用电事故;而且当分支导线截面>10mm2时靠手工绕接就难以操作。如今一种既可靠、又便捷、使用成本又低的用于大截面的干线"T”形连接的端子-XKM/JXT1系列"T”接端子的问世解决了这一难题。
XKM/JXT1 series T-type connector and T-type terminal box are used for branch line Ttype connection in the construction and industrial electric equipment when cable trunk can’t be cut off. The traditional T-type connectionmethod of conductor is to strip the insulator of trunk line, wrap the branch conductor to the trunk line, and pack with the insulated cloth. This connection method have the most direct defects which are poor reliability, large
contact resistance, easy to cause electric accident. when the branch conductor section is larger than 10mm2, it is difficult to wrap by hand. The launch of XKM/JXT1 series T- type connector, used for trunk line of largesection, solves thisproblem due to its features of reliability, convenience and low cost.
二、产品优点 Advantages
1.实 现电缆不切断时的干线分线,组态灵活。
2. 实现铜或铝导体的可靠连接,实现铜——铝过度。
3. 所有电性能指标均符合IEC国际标准,具导电性好、电阻损耗低、电压降小等优点,接触点压降 仅 为 1.98mV,是国际标准的2/3。
4. 较强耐热性和抗冲击能力,可承受120A/mm2的短路强度试验,绝缘基座采用不燃烧材料制作 、 耐 老化性能优良。
5. 安装方便,节省施工工时,不用线鼻子(端头),实现裸导体连接,深受施工队伍欢迎。
6. 与插接式母线槽及分支电缆相比,节省50%-70%的工程费用。
2. Reliable connection of copper or aluminum conductor and the transition between copper and aluminum.
3. All electric performance parameter in informity with IEC standard, perfect electricity conductivity, low resistance loss, little voltage drop, and the contact drop 1.98V.
4. Strong heat endurance and impact resistance, withstanding short-circuit strength test of 120A/mm2, the insulator foot made of incombustible material, shows perfection in aging resistance.
5. Convenient installation, saving time for construction, not need lug, realizing bare conductor connection, favored by construction teams.
6. Compared with plug-in bus ducts and branch cables, it can save 50%~70% of engineering expense.
三、结构特点 Feature
        FJT6/JXT1系列"T”接端子由绝缘基座、接线框、防护罩三部分组成,接线框由导线夹、螺钉、螺母和支承框五种零件组成,导线夹与导线接触面呈包容形的犬牙交错结构,具有接触面大、压接可靠的特点,通过不同形状的导线夹的相互组合,可形成双层接线,下层接入主干线,上层接入分支线,形成干线不断的"T”形连接。产品分为普通型和防护型,防护型尤其适合在电缆桥架中使用,安装在桥架中可以有效地防止鼠患对线路的危害。
        This product is composed of insulator foot, wire frame, protective cover. The wire frame is made up of clamp, screw, nut and supporting fixture. A closed interlocking structure is formed between clamp and conductor contact with large contact surface and reliable crimping, Through combinations of different shapes of clamps, a double-layer connection can be formed, whichmakes the trunk line be connected from the lower layer and branch line be connected from the upper layer Thus, T-type connection is formed. The produc t has common type and protection type. The protection type product is especially suitable for the cable tray, to effectively prevent the circuit being damaged by mouse.

XKM/JXT1-25mm2/5P
订货号(Order No.): 110177
四、安装与尺寸 Installation and size
        XKM/JXT1系列"T”接端子通常安装在"T”接箱内随箱体一起供货,使用时按以下步骤:
1. 打开箱盖;
2. 下取护罩;
3. 随按机说明书要求取出导线夹,装入主干线;
4. 装入分支线后盖上防护罩,盖上箱盖即可。
T-type connector is usually installed in"T”terminal box to deliver. The installation steps are as follows:
1. Open box cover;
2.Remove the protective cover;
3. Take out the clamp and connect the trunk line according to the manual;
4. Shut the protective cover down after connecting the branch line, and put the box cover on.
五、主要参数 M aint echnicalp arameter
产品型号
Product model
XKM/JXT1-25(16) XKM/JXT1-25(16)B
极数Pole 1 3 5 1 3 5
型式Type 一路干线,一路或二路分支
One-circuit trunk line, onecircuit
or two-circuit branch line
一路干线,一路或四路分支
One-circuit trunk line, twocircuit
or four-circuit branch line
外形尺寸 Outline size
(厚T/宽W/高Hmm)
31/60/81 83/60/81 135/60/81 31/60/81 83/60/81 135/60/81
电压/电流/截面
Voltage/current/
section
1000V/100A/25mm2
拧紧力矩(Nm)
Tightening torque
12
压线螺钉
Crimping screw
M8
压线范围 (mm2)
Crimping range
干线Trunk line 10-25,
分支Branch line 6-25
干线Trunk line 10-25,
分支Branch line 6-25
干线剥线长度
Stripping length of trunk lin
25
箱体尺寸Size of box
body(参考reference)
250(长L)×200(宽W)×120(深D) 250(长L)×200(宽W)×120(深D)

XKM/JXT1-25mm2/5P
订货号(Order No.): 110177
产品型号
Product model
XKM/JXT1-70(50) XKM/JXT1-70(50)B
极数Pole 1 3 5 1 3 5
型式Type 一路干线,一路或二路分支
One-circuit trunk line, onecircuit
or two-circuit branch line
一路干线,一路或四路分支
One-circuit trunk line, twocircuit
or four-circuit branch line
外形尺寸 Outline size
(厚T/宽W/高Hmm)
36/60/105 98/60/105 160/60/105 36/60/105 98/60/105 160/60/105
电压/电流/截面
Voltage/current/
section
1000V/192A/70mm2
拧紧力矩(Nm)
Tightening torque
20
压线螺钉
Crimping screw
M10
压线范围 (mm2)
Crimping range
干线Trunk line 25-70,
分支Branch line 10-50
干线Trunk line 25-70,
分支Branch line 10-35
干线剥线长度
Stripping length of trunk lin
30
箱体尺寸Size of box
body(参考reference)
300(长L)×250(宽W)×120(深D) 300(长L)×250(宽W)×120(深D)
 

XKM/JXT1-95mm2/5P
订货号(Order No.): 110181
产品型号
Product model
XKM/JXT1-95(70) XKM/JXT1-95(70)B
极数Pole 1 3 5 1 3 5
型式Type 一路干线,一路或二路分支
One-circuit trunk line, onecircuit
or two-circuit branch line
一路干线,一路或四路分支
One-circuit trunk line, twocircuit
or four-circuit branch line
外形尺寸 Outline size
(厚T/宽W/高Hmm)
36/60/105 98/60/105 160/60/105 36/60/105 98/60/105 160/60/105
电压/电流/截面
Voltage/current/
section
1000V/232A/95mm2
拧紧力矩(Nm)
Tightening torque
20
压线螺钉
Crimping screw
M10
压线范围 (mm2)
Crimping range
干线Trunk line 25-95,
分支Branch line 10-70
干线Trunk line 25-95,
分支Branch line 10-35
干线剥线长度
Stripping length of trunk lin
30
箱体尺寸Size of box
body(参考reference)
300(长L)×250(宽W)×120(深D) 300(长L)×250(宽W)×120(深D)

XKM/JXT1-70mm2/5P
订货号(Order No.): 110180
产品型号
Product model
XKM/JXT1-70(50) XKM/JXT1-70(50)B
极数Pole 1 3 5 1 3 5
型式Type 一路干线,一路或二路分支
One-circuit trunk line, onecircuit
or two-circuit branch line
一路干线,一路或四路分支
One-circuit trunk line, twocircuit
or four-circuit branch line
外形尺寸 Outline size
(厚T/宽W/高Hmm)
36/60/105 98/60/105 160/60/105 36/60/105 98/60/105 160/60/105
电压/电流/截面
Voltage/current/
section
1000V/192A/70mm2
拧紧力矩(Nm)
Tightening torque
20
压线螺钉
Crimping screw
M10
压线范围 (mm2)
Crimping range
干线Trunk line 25-70,
分支Branch line 10-50
干线Trunk line 25-70,
分支Branch line 10-35
干线剥线长度
Stripping length of trunk lin
30
箱体尺寸Size of box
body(参考reference)
300(长L)×250(宽W)×120(深D) 300(长L)×250(宽W)×120(深D)
 

XKM/JXT1-95mm2/5P
订货号(Order No.): 110181
产品型号
Product model
XKM/JXT1-95(70) XKM/JXT1-95(70)B
极数Pole 1 3 5 1 3 5
型式Type 一路干线,一路或二路分支
One-circuit trunk line, onecircuit
or two-circuit branch line
一路干线,一路或四路分支
One-circuit trunk line, twocircuit
or four-circuit branch line
外形尺寸 Outline size
(厚T/宽W/高Hmm)
36/60/105 98/60/105 160/60/105 36/60/105 98/60/105 160/60/105
电压/电流/截面
Voltage/current/
section
1000V/232A/95mm2
拧紧力矩(Nm)
Tightening torque
20
压线螺钉
Crimping screw
M10
压线范围 (mm2)
Crimping range
干线Trunk line 25-95,
分支Branch line 10-70
干线Trunk line 25-95,
分支Branch line 10-35
干线剥线长度
Stripping length of trunk lin
30
箱体尺寸Size of box
body(参考reference)
300(长L)×250(宽W)×120(深D) 300(长L)×250(宽W)×120(深D)

XKM/JXT1-120mm2/5P
订货号(Order No.): 110182
产品型号
Product model
XKM/JXT1-120(95) XKM/JXT1-120(95)B
极数Pole 1 3 5 1 3 5
型式Type 一路干线,一路或二路分支
One-circuit trunk line, onecircuit
or two-circuit branch line
一路干线,一路或四路分支
One-circuit trunk line, twocircuit
or four-circuit branch line
外形尺寸 Outline size
(厚T/宽W/高Hmm)
45/70/120 123/70/120 200/70/120 45/70/120 123/70/120 200/70/120
电压/电流/截面
Voltage/current/
section
1000V/250A/120mm2
拧紧力矩(Nm)
Tightening torque
20
压线螺钉
Crimping screw
M10
压线范围 (mm2)
Crimping range
干线Trunk line 35-120,
分支Branch line 16-95
干线Trunk line 35-120,
分支Branch line 16-35
干线剥线长度
Stripping length of trunk lin
30
箱体尺寸Size of box
body(参考reference)
400(长L)×300(宽W)×160(深D) 400(长L)×300(宽W)×160(深D)
 

XKM/JXT1-150mm2/5P
订货号(Order No.): 110183
产品型号
Product model
XKM/JXT1-150(120) XKM/JXT1-150(120)B
极数Pole 1 3 5 1 3 5
型式Type 一路干线,一路或二路分支
One-circuit trunk line, onecircuit
or two-circuit branch line
一路干线,一路或四路分支
One-circuit trunk line, twocircuit
or four-circuit branch line
外形尺寸 Outline size
(厚T/宽W/高Hmm)
45/70/120 123/70/120 200/70/120 45/70/120 123/70/120 200/70/120
电压/电流/截面
Voltage/current/
section
1000V/250A/120mm2
拧紧力矩(Nm)
Tightening torque
20
压线螺钉
Crimping screw
M10
压线范围 (mm2)
Crimping range
干线Trunk line 35-150,
分支Branch line 16-120
干线Trunk line 35-150,
分支Branch line 16-35
干线剥线长度
Stripping length of trunk lin
30
箱体尺寸Size of box
body(参考reference)
400(长L)×300(宽W)×160(深D) 400(长L)×300(宽W)×160(深D)

XKM/JXT1-185mm2/5P
订货号(Order No.): 110184
产品型号
Product model
XKM/JXT1-185(150) XKM/JXT1-185(150)B
极数Pole 1 3 5 1 3 5
型式Type 一路干线,一路或二路分支
One-circuit trunk line, onecircuit
or two-circuit branch line
一路干线,一路或四路分支
One-circuit trunk line, twocircuit
or four-circuit branch line
外形尺寸 Outline size
(厚T/宽W/高Hmm)
48/85/125 132/85/125 216/85/125 48/85/125 132/85/125 216/85/125
电压/电流/截面
Voltage/current/
section
1000V/353A/185mm2
拧紧力矩(Nm)
Tightening torque
2×20
压线螺钉
Crimping screw
2×M10
压线范围 (mm2)
Crimping range
干线Trunk line 35-185,
分支Branch line 25-150
干线Trunk line 35-185,
分支Branch line 25-95
干线剥线长度
Stripping length of trunk lin
50
箱体尺寸Size of box
body(参考reference)
500(长L)×300(宽W)×160(深D) 500(长L)×300(宽W)×160(深D)
 

XKM/JXT1-240mm2/5P
订货号(Order No.): 110185
产品型号
Product model
XKM/JXT1-240(185) XKM/JXT1-240(185)B
极数Pole 1 3 5 1 3 5
型式Type 一路干线,一路或二路分支
One-circuit trunk line, onecircuit
or two-circuit branch line
一路干线,一路或四路分支
One-circuit trunk line, twocircuit
or four-circuit branch line
外形尺寸 Outline size
(厚T/宽W/高Hmm)
48/85/125 132/85/125 216/85/125 48/85/125 132/85/125 216/85/125
电压/电流/截面
Voltage/current/
section
1000V/400A/185mm2
拧紧力矩(Nm)
Tightening torque
2×20
压线螺钉
Crimping screw
2×M10
压线范围 (mm2)
Crimping range
干线Trunk line 35-240,
分支Branch line 25-185
干线Trunk line 35-240,
分支Branch line 25-185
干线剥线长度
Stripping length of trunk lin
50
箱体尺寸Size of box
body(参考reference)
500(长L)×300(宽W)×160(深D) 500(长L)×300(宽W)×160(深D)
             XKM/JXT1-300mm2/1P
            订货号(Order No.): 110186
 
产品型号
Product model
XKM/JXT1-300 XKM/JXT1-300B
极数Pole 1 3 5 1 3 5
型式Type 一路干线,一路或二路分支
One-circuit trunk line, onecircuit
or two-circuit branch line
一路干线,一路或四路分支
One-circuit trunk line, twocircuit
or four-circuit branch line
外形尺寸 Outline size
(厚T/宽W/高Hmm)
78/108/140 234/108/140 390/108/140 78/108/140 234/108/140 390/108/140
电压/电流/截面
Voltage/current/
section
1000V/630A/300mm2
拧紧力矩(Nm)
Tightening torque
30
压线螺钉
Crimping screw
M16
压线范围 (mm2)
Crimping range
干线Trunk line 50-300,
分支Branch line 35-240
干线Trunk line 50-300,
分支Branch line 35-240
干线剥线长度
Stripping length of trunk lin
50
箱体尺寸Size of box
body(参考reference)
500(长L)×500(宽W)×200(深D) 500(长L)×500(宽W)×200(深D)
 
XKM/JXT1-300mm2/5P
订货号(Order No.): 100602

点击
隐藏

微信
咨询


扫一扫,了解更多!

电话
咨询

0577-6161 6111
客服热线