产品展示

当前位置:首页产品中心产品展示

产品选型手册

XKM系列绝缘穿刺线夹(1KV)

产品参数 Details在线订购
一、性能与特点 Function & Features
XKM 系列穿刺线夹主要适用于架空绝缘导线的接续、分支连接和接地保护,适用电压等级为10kV和1kV及以下,其主要性能和特点:
1. 安装简便。安装时无需剥去导线的绝缘层,只要按规定位置在线夹中放入主线和支线,用简 扳 手套均匀拧断力矩螺母即可:
2. 接触电阻小,线夹温升低。特制力矩螺栓确保怛定的穿刺压力,使线夹与导线达到良好的电气接触而不过分损伤导线,保证架空绝缘导线的正常使用寿命;
3. 结构密封、绝缘性高。线夹内部采用绝缘导热油脂填充,安装后整个导体形成全封闭结, 提 高构了绝缘强度和安全性;
4. 线夹适用范围广。可适用于铜铝绝缘导线、异径导红的支接、等径导线的对接,并适用铜 铝 绝于缘导线的过渡连接。
XKM series insulation piercing connector is mainly used for wire branching The applicable voltage is 10kV, 1kVand lessmore than 1kV. It has the following function and features:
1. Simple installation. The insulated layer of lead needn’t be stripped. Put the mainline and branch line into connector correctly and screw the moment nut off with a box spanner.
2. Small contact resistance and low temperature rising . The specially-made moment bolt guarantees constant piercing pressure which enable the connector to get a good electric contact without any excessive conductor damage, and guarantee the normal performance life of circuitry.
3. Sealed stunture and high surability. The internal adopts whole sealing structure and is filled with insulating heat conducting grease, which improves insulating strength and security.
4. Wide application range . It is applicable to branch connection of copper and aluminum conductor, hetero-dia metric conductor, and butt joint of isodiametric conductor. It is also applicable to transition branch connection of copper and aluminum insulated lead.
二、应用 Application
A:高层楼宇竖井电缆分支
1. 用传统方法安装并固定好主干线电缆
2. 在需做分支的部位剥开主缆外护套0.6米(切勿破坏相线绝缘层)
3. 选与电表箱间距相符的分支电缆(不超过3米)并剥离两端端头护套
4. 纵向依次安装分支器(分支器间距≥10cm)
1.Installing and fixing main cable in traditional way.
2. Stripping outer insulator of main cable for 0.6m at part that need part (don’t destroy insulaton layer for phase).
3.Choosing branch cable (not more than 3m) whose distance is the same as electric meter box, and strip insulator at two terminals.
4.Installing the separator vertically by turns (the sepatator distance is more than 10cm).
*注:
1. 使用穿刺线夹的导线必须符合国家标准;
2. 穿刺线夹的安装人员必须完全熟悉安装技术;
3. 在带电作业时,请载上绝缘手套筒扳手;
4. 穿刺线夹属一次性线夹,由于牙型变形拆卸后请勿重复使用。
*Remarks
1. The conductor used for insulation piercing connector must conform with international standard.
2. The installation operator must be familiar with installation technique.
3. Please put on insulating gloves and use insulating box spanner during hot-line work.
4. The insulation piercing connector is a kind of one-time product. Please do not use it again after dismantling because
of dental pattern transfiguration.
三 、典型应用 Mainly application
1. 灯路系统专用(坚井禁用)
2. 建筑照明、路灯、高层坚井线连接
3. 高层建筑坚井电缆户外架空线、电缆沟工厂动力供电主缆
1. Special for street lamp system (vertical shaft forbidden)
2. For connecting the building lights, street lamp, high building vertical shaft
3. For connecting the cables of high building vertical shaft, outdoors overhead wire, cable trench, factory power cable.
四、安装过程(单相线)M ounting process(single phase line)
1. 将断面整齐的支线插入分支器盖套
Insert branch line into the casing
cover of connector
2. 将分支器固定于主干线连接处,后 用然力拧紧力矩螺母
Fix clamp on the joint of main line, then twist firmly by hand.
3. 用六角套筒扳手垂直拧紧力矩螺母至帽断开螺为止
Vertically twist moment screw to break screw cap with hexagonal set spanner.
4. 用六角套筒扳手垂直拧紧力矩螺母至帽断 开螺为止
Vertically twist moment screw to break screw cap with hexagonal set spanner.
第一步:合上
First:closing
第二步:紧固
Second:firming
型号Model:XKM0-35
适用电压(KV)Applicable voltage:1
主线截面(mm2)Main line:1.5~35
支线截面(mm2)Branch line:1.5~10
标称载流Nominal current(A):63
外形尺寸(mm)Dimension:27×41×62
螺栓数量(枚)Bolt number (pcs):1
订货号Order number:110519
型号Model:XKM1-95
适用电压(KV)Applicable voltage:1
主线截面(mm2)Main line:16~95
支线截面(mm2)Branch line:1.5~10
标称载流Nominal current(A):75
外形尺寸(mm)Dimension:27×41×62
螺栓数量(枚)Bolt number (pcs):1
订货号Order number:110520
型号Model:XKM2-95
适用电压(KV)Applicable voltage:1
主线截面(mm2)Main line:16~95
支线截面(mm2)Branch line:4~35(50)
标称载流Nominal current(A):138
外形尺寸(mm)Dimension:46×52×87
螺栓数量(枚)Bolt number (pcs):1
订货号Order number:110521
型号Model:XKM2-150
适用电压(KV)Applicable voltage:1
主线截面(mm2)Main line:50~150
支线截面(mm2)Branch line:6~35(50)
标称载流Nominal current(A):140
外形尺寸(mm)Dimension:46×52×87
螺栓数量(枚)Bolt number (pcs):1
订货号Order number:110522
型号Model:XKM3-95
适用电压(KV)Applicable voltage:1
主线截面(mm2)Main line:25~95
支线截面(mm2)Branch line:25~95
标称载流Nominal current(A):214
外形尺寸(mm)Dimension:52×61×95
螺栓数量(枚)Bolt number (pcs):1
订货号Order number:110523
型号Model:XKM3-120
适用电压(KV)Applicable voltage:1
主线截面(mm2)Main line:16~120
支线截面(mm2)Branch line:16~120
标称载流Nominal current(A):299
外形尺寸(mm)Dimension:52×61×95
螺栓数量(枚)Bolt number (pcs):1
订货号Order number:110524
型号Model:XKM3-150
适用电压(KV)Applicable voltage:1
主线截面(mm2)Main line:35~150
支线截面(mm2)Branch line:35~150
标称载流Nominal current(A):316
外形尺寸(mm)Dimension:52×61×95
螺栓数量(枚)Bolt number (pcs):1
订货号Order number:110525
型号Model:XKM4-185
适用电压(KV)Applicable voltage:1
主线截面(mm2)Main line:70~185
支线截面(mm2)Branch line:25~95
标称载流Nominal current(A):276
外形尺寸(mm)Dimension:52×68×100
螺栓数量(枚)Bolt number (pcs):1
订货号Order number:110526
型号Model:XKM4-240
适用电压(KV)Applicable voltage:1
主线截面(mm2)Main line:120~240
支线截面(mm2)Branch line:25~120(150)
标称载流Nominal current(A):399
外形尺寸(mm)Dimension:52×68×100
螺栓数量(枚)Bolt number (pcs):1
订货号Order number:110527
型号Model:JJC888
适用电压(KV)Applicable voltage:1
主线截面(mm2)Main line:0.76~6
支线截面(mm2)Branch line:0.76~6
标称载流Nominal current(A):45
外形尺寸(mm)Dimension:21×27×23
螺栓数量(枚)Bolt number (pcs):1
订货号Order number:110528